Tuning boat PVC for fishing with their own hands

Inflatable keel

Inflatable PVC.

PVC boat belongs to the most popular plaquinity. It is easily going and disassembled without requiring its own garage. But she has its drawbacks. Rubber design is less reliable than a tree or metal. Proper arrangement of an inflatable boat will make it suitable for long journeys.

It can be upgraded to infinity, but it should be started with compulsory tuning:

  • Private bar. The external part of the bottom can be enhanced by a private bar and PVC slices. This durable wear-resistant ribbon will help not only strengthen the bottom, but also strengthen inflatable boards and keel. By the same item you can strengthen the traum. The outer surface is dried. Carefully scrapes dirt and sand, then it is degreased by gasoline. For the bottoms are cut on paper PVC sheets. They are superimposed on the surface, after which they leave for some time warm. The sizing takes place with a hair dryer (additionally heating layers) and roller.
  • Aluminum structures. The solid floor tends to deform inflatable cylinders. To reduce friction in straight boats, duralumin stringers are used, which are installed in places of contact of cylinders and bottoms. Aluminum tubes are used for feed baskets carrying tanks with gasoline and water, as well as boxes with food. Dural Bracket without any problems withstand the echo sounder sensor.
  • Leryal washers. This design element holds a leather cable throughout the perimeter of an inflatable boat. In the process of upgrading, you can use them to secure the transaction, awning and a variety of fittings.

With NDND

Manufacturers of modern inflatable boats produce a lot of comfortable and useful details, in addition to standard equipment.

Here is a list of the most important components that can be installed:

  • Tape protector - glued along the protruding line of the inflatable side, in order to avoid unsuccessful mooring. Ribbon for amplification can prevent water from entering the boat.
  • Soft seat - will provide maximum comfort during a long stay on the water. A folding or removable design will allow holding a seat in the desired position.
  • The boat tent - will save from the hot sun in summer and rain - in rainy weather. Its installation will take several minutes, and the benefits will be assessed instantly.
  • Runduk is a very valuable fisherman satellite installed on the nose of the boat. It stores equipment and other useful things. Under the seat you can arrange a soft bag.
  • Mounted trauma - need for a motor boat. But we should not forget that even the most chic hinge trauma will not withstand the engine with a capacity of more than 2.5 liters.
  • Transit wheels - a very convenient device for transporting a boat with a motor over long distances.
  • Hard bottom - has a plate structure. Spinning lovers know what it is like - stand on a non-solid soil. The hard bottom allows you to freely move in the inner space, but each new plate adds weight.

Tuning of Soviet and modern PVC and NDND boats may be inexhaustible.

Recommended events and options for tuning boats PVC

The indisputable plus of modern tuning for PVC boats is that many details, attached equipment, fasteners and such necessary trivia are bought in special or simply shop stores. They do not need to invent and produce from the remedies.

The configuration of boats from manufacturers often does not correspond to the expectations of buyers in terms of comfort, functionality and safety. But this is quite forgiven, since the goals, tasks and concepts about each of their own. After all, almost every thing, from a beloved chair to the car you need to fit precisely "for yourself."

Popular objectives of improvements:

  • Wear resistance. This parameter is extremely understood. When a sufficiently expensive thing is bought, for recreation, work or hobby, I want it to serve for a long time and did not bring inconvenience with frequent repairs and complex maintenance.
  • Comfort and appearance.
  • Safety equipment and passengers.

The last two points include manipulations to strengthen the design, insurance, installation of additional equipment and care for the comfort of passengers.

Tuning PVC boats to increase wear resistance

An increase in reliability, wear resistance and stability is achieved through strengthening the design of the bottom and sides of the vessel. There are two approaches to strengthening the bottom of the PVC boat. You can strengthen the details separately or apply a private bar for the bottom as a whole. That is, take a wide ribbon and take it completely. Moreover, this will not affect the undercarition characteristics of the Floor. True will have to remove the installed dran, and put them on top of the amplification. The only minus will be that the wide ribbon is harder than somewhat narrow. But when careful, accuracy and the right selection of glue, it can be perfectly done on your own.

Strengthening bottom

If you start upgrading from the bottom, then it is worth considering several useful works: strengthening the keel, cylinders, a transom, and so on. The bottom of the bottom is added with the help of a special PVC tape (private timber). This is a very relevant procedure for the soft bottom. After all, when drinking spinning, cuttings and movements by boat on water often have to make sharp movements, which does not contribute to the preservation of equilibrium and can end with spoiled fishing due to falling into water. And after the reinforcement, the bottom becomes harder, but does not lose elasticity.

The second reason to strengthen the bottom will be dangerous to flow into the root. Sharp and thick branches or stones can not be noticed when the vessel is moving, especially in standing turbid water. At the race at an obstacle, the reinforced bottom is there is a chance to damage only an additional layer and repair too only it. It will save time for repairs, the contents of the wallet and will continue fishing even after the accident.

Strengthening keel

The increase in keel is called PVC ribbon over the factory tape at Kiel. Also strengthen Kilson. This is added strength and rigidity.

Strengthening cylinders

The integrity of the property depends on the strength of cylinders, and sometimes the life of a fisherman. Reinforced cylinders are an opportunity to reach the shore on the boat dry while maintaining all its contents. Cylinders constantly experience a load from air pressure inside and compensatory water pressure from below, which leads to increased wear of this part of the vessel design. Strengthening cylinders using the same PVC tape will add not only strength, but also stiffness of the cylinder form. The tape passes on the bottom (sometimes additionally on the side) side of the cylinder.

Increase transaction

The trauma is simply necessary, because it is protected by only one layer of PVC fabric. When moving at high speed, this part is deeply immersed in water and has every chance to hook an obstacle. And when the other elements are gained, it is necessary to give it additional rigidity to preserve the bottom of the bottom.

Installing Stringers

Stringors are installed in the presence of hard while in the boat. In fact, Stringer is a piece of duraluminum profile, straight and hard, so it is not installed on the nasal roundings. The appointment of this procedure is the rescue of PVC fabric from abrasion and the formation of holes, due to the friction during the deformation of the vessel during the navigation. Hard edges of the floor relate to inflatable elements and can lead to a violation of strength.

The habitat view of VEYN

Inhabit the view (fish) in the quiet places, where there is at least some amount of liquid tinted soil, is swamps, river old men, ditches and pit, deaf trench lakes, swampy creek, or strong ducts, small quiet rivers.

In the dry time, the view is buried in a wet tina, which remained at the bottom of the dried ponds and streams, to a depth of about one or two meters and flows there to the hibernation state, which stops with the arrival of rains. As a trout cannot live without flowing clean water, and the view is unable to dwell without her tina, which for him serve as a favorite refuge.

Fastener

All additional elements are attached to PVC boat with two-component glue. There are several models of universal fasteners. If you install it, you can adjust any items to it.

Fastening "Pile"

Universal fastening element designed to fasten the fishing rods, awnings, tables, etc. The main material of its manufacture is PVC. Fasteners of fasteners "Pyk" - height 35 mm, diameter 20 mm.

Fastentm fasteners

This is universal, but quick fasteners. It is capable of transforming for any attached equipment, such as echo sounders, navigators, belt holders, etc. It allows you to quickly move from one type of fastening to another.

If you install all the elements on the boat, the above elements, then their weight can significantly add the weight of the boat and then in the hands of it already do not go down to the water. Therefore, before proceeding with such tuning, you should think well.

Tuning boats PVC do it yourself

Watch this video on Youtube

02/14/2017

Sitting

Strengthening bottom

Although PVC fabric, which is used in the manufacture of boats is durable, but it is still a fabric. It is susceptible to abrasion about the stony or caustic bottom and is not insured against the gusts of the spikes, branches and other troubles. Strengthening or booking the bottom It is originally what needs to be done within the framework of the PVC boat tuning.

The gain as it is possible to replace, and this is better than subjecting a "native" fabric to repair.

Calculate that when strengthening the bottom of the boat, 8 - 9 kg of weight will be added and its dimensions will increase if you are placed on bags.

You can strengthen individual places that are most susceptible to scuffs, or completely glue. Often, speaking of the full or partial strengthening of the bottoms, the term "booking" is used.

The enhancement of the vessel is made by sticking the additional PVC tape, it is also called a "profile", a private bar. PVC tape (private timber) is of different thickness from 1.2 mm to 3 mm. The tape is glued to two-component glue.

The range of the width of the private bar ranges from 60 to 235 mm. Prival Bar softens the wave blows. It happens usual and with a bump. Some boats are already equipped with such a bar in the basic configuration.

Strengthening the keel - it consists in gluing an additional layer of tape (private timber) over the factory tape. This strengthening in addition to keel covers and kilson.

Strengthening cylinders - optionally to do along the entire length of the cylinder, usually tape (timber) is glued partially as needed.

The enhancement of the transaction is since the trauma protects only the PVC fabric layer, then the gain is very needed. Tracks are enhanced by a private timber. You can roll the baton battle completely.

All amplification can be done independently. The main thing is to observe accuracy and choose the right glue.

Installation of stringers - Duralumin alloy profiles, are installed in the presence of hard sex, these are additional ribs of stiffness, their size corresponds to the thickness of the Piol (rigid floor).

The inflatable boat when driving is experiencing a deformation, rigid Pioles rub about the inflatable parts of the vessel Stringors protect fabric from abrasion.

In the nose of an inflatable boat, where it has a curvilinear profile, the stringers are not attached, they are not needed there.

How to apply a private bar

In order for your own hands to accommodate the ram, you will have to do the following:

  1. Rinse the bottom of the boat, remove the grains from it or other foreign items and dry.
  2. Declaring the surfaces glued, can be gasoline, vodka, alcohol, acetone, but when using acetone, do not rub much, damage the PVC fabric.
  3. Apply a brush thin layer of glue and on the surface of the boat and bar, leave it for 15 minutes, then apply a second layer and wait for drying so as not to stick to the palms.
  4. To accurately impose a timber on the surface, press.
  5. For better gluing, the surface must be heated, it is possible to make it an ordinary household hair dryer. Heat so that the bar is not melted, and the fabric did not start bubble, without fanaticism.
  6. Once again, to give a bonded place and rolling on it with the subject of a rounded form, such as a bottle, for the final clutch.

Engine insurance

Unfortunately, it is impossible to predict that it can happen to a boat after going into an open reservoir. Pretty frequent troubles in fishermen are unexpected collisions with obstacles. In this case, the poor cutting of the clamps can provoke a disruption of a boat engine from the location. Very often he simply goes to the bottom of the reservoir.

To eliminate this kind of misunderstandings, the engine strengthened. For this, the cable (synthetics or steel) is stretched (synthetics or steel) on the trans. bypassing ry-rings, which are placed on the trans. Speaking by a simple yazik, the motor is reliably asleep and it becomes impossible to lose it.

Increase transla

The normal height of the deadwood is 381 mm, but even in the engines of one manufacturer, it can be discharged by 20-25 mm. At the expense of the ideal position of the engine, you can increase the speed of the flooded and rebuild the splash of the boat. If you put the motor, and the anti-catalyst plate at the calibration below the desired level, you can release the screws and set the appropriate height of the transom, and then perform trial races. If you need to change the suspension engine, you can adjust the trauma for the characteristics of the new motor, in particular, under the size of its deadwood.

https://youtube.com/watch?v=VideoSeries.

In the next video you will find a great example of tuning boats PVC with their own hands.

Manufacturing Targy

For boats from polyvinyl chloride will be to the place of Targa, equipped with a number of glasses, or a holder on a clamp. The procedure for creating target consists of several steps.

  • You need to take a plastic or iron tube, the diameter of which will be larger than the rod diameter by 0.7-1 centimeter. It is necessary to bend the arc into the width of the boat.
  • On both sides, the tube must be flattened and drilled holes under the mounting bolts.
  • Part of the tube must be cut into glasses, from one edge of which you need to privar the plugs.
  • The glasses are fixed with arc welding for trolling.
  • At the end, all the adaptation is treated with a skin and apply waterproof paint.

Creating a holder like clamps:

  • From an old meat grinder, you can make a clamp by cutting the upper part from it;
  • After you need to drill a few holes in the bodies of the meat grid, which will perform the role of holder racks;
  • In the tube it is necessary to drill 3 holes, the third should be in the upper area;
  • The rack made from the clamp and the flattened tube must be associated with bolts and washers;
  • In the hole, located at the top, it is necessary to fix the sanitary clamp.

Tuning boats do it yourself - options for modifications, tuning directions and improvement of serial PVC boats (130 photos and video)

In specialized boats stores, mostly sell without all sorts of missions, so for convenience, each fisherman equips her at will. And this applies not only to PVC boats, although they are mainly subject to refinement.

Today we will look at the possible options for tuning boats for fishing with your own hands and tell me how to make some of them.

Tuning boats from PVC

This water vehicle is the most sold and convenient to use. This can be determined by the fact that:

  • the boat is easy to transport, do not buy any trailers;
  • It is easy to repaired;
  • For her there are many lotions.

But even considering all these positive moments, it is quite practical in the "cheese". The functionality of such a means is very small, which means that it is necessary to refine.

There are services where you can exercise your venture, but it costs quite expensive. Make tuning PVC boats will be cheaper and more correct.

Of course, this does not mean that all the details need to be mastered personally, some of them can be purchased in the store.

So let's look out that you can finish:

Strengthening the bottoms and cylinders. Such tuning experienced fishermen is always carried out, regardless of the conditions of the fishermen. It is proposed for the bottom and on the sides of the cylinders to glue an additional layer of rubberized fabric or membrane.

Initially, at an inflated boat, measurements are made and places are noted where the marks will be glued. After this, the boat is blown away, the places of gluing are degreased, and the selected material is glued on top.

If necessary, at the end, they still warm the hairdryer (construction). With such tuning it is worth considering that the weight of the boat will increase by an average of 5 kg.

Anchor. Very comfortable thing when fishing in one place. The stores sell a special anchor ryy, it is installed on the stern.

Sealing seams. When buying a cheap boat, you do not have to hope for quality. Therefore, many owners additionally seal seams.

You can also decorate the boat around the perimeter by various stickers, etc. To be able to inspire, you can see the photo of such tuning on the boat with your own hands.

Holder of rod. Also an indispensable thing, if fishing occurs at once a few spinning.

To get acquainted in more detail, we offer to watch the video tuning boats with your own hands.

Tuning fiberglass boats

In the case of such an aggregate, the variations of tuning are almost similar to the past. The main thing is to initially think about what you need for what purposes a boat will be used.

If for fishing, you immediately need to install spinning holders, anchor ryy and so on. When the tool is used as a family pastime (just swim), you can install seats such as rear and front.

You can even build a kind of boat, create a scheme, from the OSB panels to cut all the details and install directly on the boat housing. Then paint, open lacquer and dissect by waves.

The tuning of the fiberglass boat is not difficult to make, the main thing is to have a desire.

Aluminum boat tuning

These boats, like PVC, use the people in great demand, and causes this the strength of the hull, now no snag will be able to interrupt all fishing.

You can add such a tool:

  • Seats (if there is already there, then drag);
  • Windshields;
  • Additional covering of the housing in the form of chromium;
  • TEN (SPA);
  • Remote control, etc.

In addition, you can make a painting of the vessel. In general, make a mini yacht, in which it will not only be pleasantly riding, but also to swim for a kilometer from the shore and enjoy the open sea, drinking cocktails.

The tuning of the aluminum boat is very similar to the previous one.

Conclusion

As you could already guess, it all depends on your imagination and desire. After all, this is the fundamental success.

The main thing is not to be afraid of difficulties. Boats are a very good vehicle and attaching their hand to modernize them, you can recreate something unusual.

Tuning PVC boats is the improvement of technical indicators and characteristics, which helps to facilitate the fishing process and make it more productive. This may include changes in the appearance or installation of new internal structural elements.

Tuning boat PVC

Why do you need tuning?

Such work on improving the vessel can avoid the cash costs for the purchase of a new boat. You can approve the appearance and technical capabilities of an existing swimming agent.

Refinement of the PVC boat for fishing with their own hands helps to increase the level of safety of person on this vessel during fishing, and also allows you to increase the life of a swimming agent. To improve these functions, the following works are carried out:

  • set the parking anchor;
  • equip a means protective awning;
  • Modernize the armchair of the fisherman;
  • equipped with a vessel with various bags for storing the smallests required for fishing;
  • Mount the campaign table;
  • make a similar staircase;
  • Install an electric or gasoline power unit;
  • Make a sail;
  • Mount fasteners for rods, gas tank and echo sounder;
  • Install special pumps for boats.

All of these work on modernization make it possible to increase the level of comfort and security of the fisherman. The user can strengthen the bottom of the vessel, make a hard floor, increase the level of protection of sides of mechanical damage, set fasteners for additional safety ropes and ropes. And to increase the service life, it is recommended to use parking and transport covers made for such boats.

Strengthen the bottom

When strengthening the bottom, it is necessary to take into account the following factors:

  1. The weight of the inflatable boat can increase to 12 kg, and the overall parameters are 20-30 mm.
  2. Recommended material for amplification - tapes for tuning PVC.
  3. The thickness of the mounted material should not exceed 50 mm.
  4. Strengthening strips of the central part of the vessel and torpedo gives a small additional protection and gives stability. And the strengthening on all the bottom will increase the service life and safety several times.

Tuning PVC Boat Tuning

As a material, you can use strips of plastic, aluminum or duralia. They are fixed using special rivets on the central part of the bottom or on the back of the vehicle.

For this procedure, you will need the following tools and details:

  • Material for amplification recommended - PVC thickness of 30-50 mm;
  • Construction Scotch;
  • construction hairdryer;
  • Special glue for PVC;
  • Cardboard patterns boats;
  • roller;
  • Alcohol or solvent to remove fat.

Inflated boat must be flipped over and clean the bottom from dirt and dust. From the prepared material, the necessary shape is cut with scissors, applying cardboard patterns. Using a rag, degrease the working surface of the vessel using a two-component solution or alcohol. Scotch glued along the loop contour.

Before applying glue, the workpiece must warm the hair dryer.

The glue itself should be applied in 2 layers: the first must be thin, and the second can be applied only when the first will dry, but does not dry completely. The workpiece is installed on the bottom. It should be smoothed using a roller. Depending on the adhesive used, you need to give a ship to dry for 2-3 days.

Inflatable keel

Inflatable keel is an element that the PVC boat must be equipped with a length of more than 3000 mm. Such an element prevents the vessel tipping during a high speed of movement and makes it possible to accurately follow the intended course. It creates an additional burden on the front part, which allows you to leave the boat afloat. Each fisherman can make such equipment independently.

For homemade inflatable keel, elements are required as:

  • Dense boat fabric from PVC;
  • glue;
  • valve;
  • As a prival bar, you can use PVC stripes;
  • mustard solution.

Kiel for tuning boats PVC

Tuning boats from PVC - Making an inflatable keel:

  1. Of the pre-prepared material, it is necessary to glue a small tube with a diameter of 100 mm, on which the valve must be set. The length of such a device is calculated taking into account the distance from the forage part of the transport to the nose.
  2. Then you need to glue the made tube to the surface of the bottom in the inner part of the boat in a place for keel. At the same time, the PVC stripes may be required.
  3. After that, a mustard solution is poured into the pipe, which will ensure the required level of tightness. Before the fill, such a solution must be frightened well.
  4. It is necessary to remove the vehicle in shallow water and pull the air from the keel.

If you need to strengthen the existing keel, then you can glue the PVC tape over the factory tape.

Strengthening cylinders

Strengthening cylinders increases the likelihood of staging to the shore without turning the boat and loss of all content. These elements are under constant pressure of the air flow from the inside and compensatory water pressure outside. All these factors lead to premature mechanism wear. It is possible to strengthen it using PVC tape. It is attached on the lower and side sides of the cylinder.

In order to properly strengthen the cylinders, you must perform the following steps:

  1. Buy special colors from PVC or make them independently. In stores you can find a habit of a boat size of any modification. And for independent manufacture, it will take waterproof material from which you need to cut a piece corresponding to the sizes of the cylinder.
  2. Before gluing, you need to degrease the working surface with a special solution or alcohol. To connect, it is recommended to use PVC glue.
  3. After the end of all the work on the modernization of cylinders, it is necessary to give glue to dry for 2-3 days.

You can also install an onboard share that will protect the outer part of the cylinders during the mooring or when a collision with various obstacles. If such a halt will be equipped with a splashper, the cylinders will be protected from the backwater wave. The size of such an element can be from ¼ to ¾ of the length of the entire cylinder. In some cases, the installation of stringers may be required, because Many boats have a nasal balloon have curvilinear circuits.

PVC boat stringers

Making an anchor fastening

Anchor fasteners are attached to accessories for tuning boats from PVC. The weight of this element should be at least 10% of the mass of the entire swimming vessel and not more than 1% of its length. With its manufacture, it is necessary to take into account the following points:

  1. The maximum height of the waves on the reservoirs where fishing passes.
  2. The greatest strength of the wind.
  3. The nature of the bottom of the boat.
  4. The strength of the cable to be used for anchor. It should be borne in mind that it will be subjected to strong loads: the more the weight of the vessel, the more efforts the cable should be calculated.

For the manufacture of anchors for the PVC boat, the following items will be required:

  • Metal tube with a diameter of 25 mm and a length of 270 mm;
  • fasteners;
  • 4 metal segments;
  • 2 metal rings.

To the tube you must attach the sleeve. Strips will be used as a paw. All elements are fastened with each other with nuts and screws. In order not to lose anchor, it is necessary to attach to the beeke cable. In this case, the fisherman will always know where he threw anchor.

In order to make this mechanism, heavier can be poured into a metal pipe lead.

It is necessary to select a design in accordance with the reservoir, which passes fishing. The mechanism must securely hold the ship in one place, and it should be conveniently removed from the hooks.

Holders for Spinning

For a large number of spinning, a tuning boat is made in the form of installation of various holders. They can be connected to the hull of the vessel with the help of elements such as:

  • bolts;
  • screws;
  • clamps;
  • glue.

For boats from the PVC material, Targa is suitable, equipped with several glasses, or a holder on a clamp.

Targy manufacturing process for boat:

  1. It is necessary to take a plastic or metal tube, the diameter of which will exceed the diameter of the rod by 0.7-1 cm. From it you need to aback the arc in the width of the swimming agent.
  2. From the 2 ends, the pipe should be flattened and drilled holes for fastening bolts.
  3. A portion of the pipe must be chopped into glasses, on the one hand it is necessary to weld the plugs.
  4. Glasses weld on the arc.
  5. At the end, the entire design is sandwiched and covered with waterproof paint.

Production of a holder in the form of a clamp:

  1. From the old meat grinder you need to make a clamp by cutting off the top of it.
  2. Then you need to drill a few holes in the meat grinder housing, which will be used as holder racks.
  3. Three holes should be done in the pipe. The third should be located at the top.
  4. The fabricated tube and clamps are made using bolts and washers.
  5. In the upper hole, you need to attach the sanitary clamp.

Seat installation

In order to set the seat of the turning type, make marking and decide on the size. Then mounted on the cylinders special holders under the stand. After installing these elements, you can start installing the rotary mechanism. The seat itself is attached using 3-4 nuts with studs. Recommended method for installing soft seats - belt. In this case, it will be fixed using 2 durable belts.

For the manufacture of an inflatable chairs for a swimming vessel from PVC, the following materials will be required:

  • waterproof fabric;
  • tape for connecting joints;
  • waterproof seam gluing adhesive;
  • polyamide threads;
  • scissors;
  • Plate sheets.

It is necessary to measure the seat parameters and make the pattern. Then transfer it to the fabric and cut with scissors. Ready items need to be brought into the pipe and sew along the edges using polyamide threads. Then you can move to gluing the compounds both from the inner and from the outside. In the lower cylinder, place the valve for injection of air. All items are collected in the upper and lower block, and then docile together. In order to check the tightness of the finished inflatable armchair, it is necessary to place the design into the water.

Fasteners for mounted equipment

Littros for PVC boats is used to fix mobile seats, blocks for rods, removable table, inflatable cylinders to a hard case etc.

Liktros for PVC boats

For making your own hands, such a fastener for PVC boats will require a special waterproof tissue with a density of 750 g / m². For gluing you need to cut a strip of 120 mm width; Length is selected depending on the requirements. It is necessary to apply glue on board, give it to dry, and then heat it with a hair dryer. After that, you can attach a rack, all align and remove the folds. All seams must be carefully smoothed. Excess glue is removed using a rag moistened in a solvent.

As a fastening for a gas tank, you can use a rope passed through a semiring. Rings need to be glued to the bottom with the help of waterproof glue. Instead of the rings, you can use rows or screws.

Tuning boats PVC do it yourself

Such a concept as "tuning" means improving, refinement or modernization of the product. In this case, the refinement of PVC boats. A wide-scale "tuning" of such boats costs considerable funds, especially since it involves improving the design or individual elements of the PVC boat design.

The reason for the modernization of the floating agent can serve as various factors. The first factor includes its imperfect appearance associated with the purchase in the "Ancient" time when few people wondered about the perfection of the product. The second factor is very serious and is associated with the financial side of the case. People buy not expensive things with the hope that they improve them without spending a lot of money. In addition, modernization can be carried out gradually, which will not lead to instant costs. At the same time, it should be remembered that in the process of refinement only to install only the necessary and useful elements, improving product characteristics. Although everyone has the right to decide which innovations are suitable for floating agents.

Many items can be purchased and installed on the boat. They are not necessarily made by himself, especially since this process can delay in time.

Strengthening bottom

PVC fabric that serves as the bottom of the boat is rather durable, but it is inconvenient to move. Since the bottom is not tough, then each fisherman is experiencing a number of inconveniences. Therefore, the reinforcement of the bottom is the first task. In the future, it will have to repair the amplification, but not the bottom of the boat. It will cost cheaper, and it will be easier to replace strengthening to new or repair it. You can produce both complete and partial strengthening of the bottom of the boat.

Strengthening the bottom is made by gluing a special PVC tape, which is called a "private bar". A private bar may have a thickness of 1.2-3 mm with a width of 60-235 mm. It is attached using 2 component glue. This will make it possible to make the bottom more rigid and more protected from different underwater surprises.

Strengthening keel

The operation is reduced to the fact that the PVC tape (private timber) is glued on top of the factory tape). Such an increase is applied to killya.

Strengthening cylinders

Strengthening is based on the need. Cylinders are also subjected to constant wear.

Increase transaction

For this element of the boat, the gain is simply necessary because the traum is protected by only one layer of PVC fabric.

In order not to suffer with individual elements, the bottom of the boat can be launched completely by applying a private timber. To be attentive and neat, as well as choose the right glue, then the operation can be done on your own. A similar approach will solve many problems associated with the deterioration of the boat characteristics.

Installing Stringers

If a rigid floor is installed on the boat, you will have to install duraluminum profiles. Since the boat is deformed while driving, the rigid paisols of the floor relate to the inflatable parts of the boat and the process of friction occurs. This can lead to abrasion of the fabric, which is undesirable and can lead to a violation of the strength of the boat. In the nose, where the boat profile has a curvilinear form, the stringers are not installed.

Independent fastening of a private bar

Independent strengthening of PVC boats consists of the following operations:

  1. The boat is washed away, after which all pollution is removed. After that, the boat will dry as closely as possible. It should be remembered that the slightest moisture remnants will not allow the boot elements qualitatively.
  2. Bled surfaces are degreased by gasoline or acetone. Degreasing is taken carefully, so as not to break the fabric.
  3. With the help of a brush to the surface, a layer of glue is applied. Usually the glue is applied to the boat and a private bar. After 15 minutes, the second layer of glue is applied. The layer dries up until the glue stops sticking to the hands.
  4. The timber is superimposed on the surface and pressed.
  5. So that the surfaces are securely glued, it is better to heat them with a hair dryer. Heating is carried out very carefully so that the plastic does not start melting.
  6. After that, the glued surfaces are pressed again with maximum effort.

Roots by boat.

Such elements make a boat more stable. REDs are PVC elements with different shapes.

Anchor

The PVC boat anchor is a mandatory element that allows you to install at any point of the water area. Especially effective in the presence of a flow when the boat can leave from the planned place.

Spinning holders

Very useful accessory. Special attachments can be purchased in the store. The optimal option for one - 2 mounts, for two - 3 fasteners. Extra fasteners may be a hindrance. Finding in the finished state of a large number of spinning is not desirable. If necessary, they can be pulled out of the tube at any time.

Alternatively, rod holders can be made from PVC pipes. They can be easily purchased in construction stores.

Transom

Under the engine, the trauma is required. Buying a boat, a tramer can enter a complete set or not. It is advisable to install a echo sounder.

Anchor rim

It is installed on the stern of the boat and facilitates the process of lowering and lifting anchor. The roller is located somewhat lower, so that the abrasion of the private bar does not occur.

Transit wheels

Set them or not, depends on the nature of the reservoir. Most reservoirs, especially wildlies do not have conditions for normal boat descent. In such conditions, you have to get a boat on your hands. And therefore, no transit wheel can do any speech.

Inflatable keel

As a rule, simple boats are not equipped with a keel that does not allow her to adhere to the course. If you install an inflatable keel on it, it will help solve the problem of boat stability, especially if there are waves.

The magnitude of the keel depends on the length of the boat. If you set a boat on a boat having a length of less than 3 meters, it will provoke the rise of the nose of the boat. This element is attached using special ribbons, which are part of the configuration.

Seat

Almost all models of such boats are equipped with hard seats, which is not very convenient because you have to sit in one place. So that the fishing is in joy, it is better to replace the seating to soft or modify the old ones. Most boat owners make seats on the type of winter fishing, when under the seat there is a drawer for accessories.

Alternatively, you can construct a moving seat that is installed at any point.

Installing bags

The bag can be equipped under the seat or in the bow of the boat.

Boat engine insurance

Fishing is an interesting, but also a dangerous occupation. It is sometimes difficult to predict what can happen on fishing. Quite often, when freelance situations intervene in the fishing process, a motor disruption occurs. As a result, the motor simply goes under water. That this does not happen, the motor is insured using a steel or artificial cable. It is fixed to the transntion through 2 rhy-rings. In other words, the motor is simply tied.

Fastening of the benzobaca

Elements such as an additional canister for gasoline require mandatory attachment. This is necessary so that when moving or sharp turns, the canister could not change its location. Mounting is carried out by rope and half-colts attached to the boat. They are attached to the boat as follows:

  • semiring glue to the bottom if it is from PVC fabric;
  • Scuffed screws to Piyolam if the floor is hard.

Fastener

All additional elements are attached to PVC boat with two-component glue. There are several models of universal fasteners. If you install it, you can adjust any items to it.

Fastening "Pile"

Universal fastening element designed to fasten the fishing rods, awnings, tables, etc. The main material of its manufacture is PVC. Fasteners of fasteners "Pyk" - height 35 mm, diameter 20 mm.

Fasten fasteners TM.

This is universal, but quick fasteners. It is capable of transforming for any attached equipment, such as echo sounders, navigators, belt holders, etc. It allows you to quickly move from one type of fastening to another.

If you install all the elements on the boat, the above elements, then their weight can significantly add the weight of the boat and then in the hands of it already do not go down to the water. Therefore, before proceeding with such tuning, you should think well.

Having bought PVC boat, sooner or later each owner thinks about improving the technical and functional characteristics of the swimming agent. Tuning can be ordered from proven masters, which fee can embody any desires for the client. However, the most interesting process of self-conducting tuning, which not only improve the characteristics of the boat, but also delivers a lot of positive emotions.

PVC boat at repair

Strengthening boat construction

Tuning should begin with strengthening the bottom surface. Despite the fact that manufacturers pay materials for the bottom increased attention, over time it wear out. Actively using a swimming remedy or carelessly jump on the stones, you can hardly damage the bottom.

Help in this situation can stick a profile made on the basis of PVC. However, when the bottom surface is improved, it is worth remembering that the profile will increase the mass of the vessel. Maximum strengthening the bottom is recommended only in cases of permanent use of a swimming agent on fast rivers with a stony bottom. If fishing is made on a quiet reservoir, the strengthening of the bottom surface can be made minimal.

What may be necessary to strengthen the bottoms:

  • PVC membrane or corresponding profile;
  • The adhesive basis of PVC "Viknikol" or "Uranus".

If desired, it is possible to strengthen with the membrane without using the adhesive basis.

Step-by-step process:

  1. The surface of the swimming agent is washed away from the sand.
  2. Degrease the clean surface.
  3. Removing the valve, disconnect the transit wheels.
  4. On the swimming facility (inflated) paper unfolds and 2 patterns are cut out According to the size of the bottom surface (area between the location of cylinders and keel).
  5. According to the resulting patterns, it neatly cut the elements from the membrane. The mass of one piece is commonly slightly less than 2 kg, and the thickness exceeds 1.5 cm.
  6. Carved material folded outdoors Where the sun's rays fall until the complete adoption of the desired shape of the product.
  7. Turning on the hair dryer, warming up all the details and squeeze In this case, air with roller.
  8. We work out the extreme areas very well. Bonding materials is performed by heating the membrane material from the effects of high temperature regime.
  9. PVC profile stick to the keel on both sides. This will prevent Kilson.
  10. Strengthening the boat is also made On cylinders (on a quarter of their length).
  11. If desired, you can strengthen the boat and the transnt (It is covered only by a layer of bottom woven base).

How to apply a private bar

The reinforcement of the timber can be performed with their own hands according to the instructions suggested below:

  1. We wash the surface of the bottom of the swimming agent. We remove the sandy raids and dry.
  2. The dried surface is degreased by vodka, alcohol or gasoline.
  3. Using a brush, we applied a thin layer of the adhesive base to the surface of the bar and the vessel.
  4. We leave for 20 minutes, after which the second layer is similarly applied.
  5. We wait for a complete drying of the material (it should not stick to the hands).
  6. The extremely accompanying bar is tightly pressed against the surface.
  7. To ensure the maximum degree of adhesion, you should pre-warm the surface with a hairdryer.
  8. Overgrown the place of gluing and ride a rounded weighty object on it.

Installation of the Red

Redan is called a kind of profile with the presence of a guide (mostly resemble the form of a triangle). Equipping the swimming agent, it is possible to increase the level of resistance of the boat on glide. You can combine the placement of the renovation with the application of additional prophylaxis for keel and cylinders. Short routs can be placed in the nose of the bottom (intensive formation zone of spray).

Installing Stringers

Before starting the installation of stringers, make marking:

  1. Having placed the Piol kit on the floor, we provide exactly copied oddness how they are placed in the cockpit.
  2. Stringer is applied to one side of Piole By observing the overlapping of three neighboring Piol.
  3. In the nasal part of the vessel, the Stringers are not recommended. When gliding, the main load falls on Pioles of the third rear area of ​​the case of the PVC product. Based on this, it is more expedient to install Stringer to extreme Pioles from the transit part of the boat.
  4. It is very important that when installing Stringers, Paiolins did not drank over the edges. To ensure this condition, the layout of the depth of propyl, which will ensure the dressing of Stringer on the extreme region of plywood.
  5. For markings, we apply Stringer and align it on the plane of the extreme parts of Piol. Observing the size of the profile, the contour of the contour for propyl (on both steerger edges).
  6. Connect the markup of one line And we get the desired maximum accurate markup of one side.
  7. Putting the cuts for the stringer, you should make a long time for a length of about 4 cm (from each side). This will allow you to comfortably dress and shoot a stringer if necessary.
  8. The average Paioline during the markup is slightly shifted in the opposite side of the area placed. After that, there should be marked from the second side of Piol.
  9. After graduating markup and taking a jigsaw, proceed to drinking on the markup of pockets (To establish stringers). Prevent the appearance of chips on the plywood if you can use files "on wooden materials", which have small cloths. When working, it should be done without hurrying in order not to make mistakes.
  10. After performing all actions, increasing the extreme cuts of Piolin slightly and processed them impregnating water-repellent type. It is perfect in this case Pinotex Focus, which contains in sufficient wax. If desired, extreme sections can be treated with oil (well-heated) or a yacht varnish (waterproof). Compliance with these recommendations will prevent Paiolin's swelling.
Boat on the bank

Equipping the swimming agent by the rifle can increase the level of resistance of the boat on glide

Hard floor

In the manufacture of hard floor, do not do without:

  • List plywood (10 mm);
  • loops - about 20 pcs.;
  • bolts;
  • nut;
  • yacht varnish;
  • impregnations;
  • Washers.

Step-by-step process:

  1. First of all we make suitable in size characteristics bottom pattern from linoleum.
  2. Width indicators (We take into account the rectangular part of the bottom) should be more than 1.5 cm to ensure normal gaps.
  3. Cutting the linoleum, we will carry out the markup of the rigid gender. It will be placed between the floor (hard type) and PVC bottom covering, which will prevent damage to the accessories available.
  4. The pattern is folded in half and with the help of circumcision Its symmetry is achieved.
  5. Putting a plywood sheet , gently cut out six Piol (width 80 cm).
  6. Square left If desired, it can be focused on the legs.
  7. Long sides of Piolin curly using a file. We impregnate the impregnation of the protective type.
  8. From Paiolin collect for the surface bottom harmonica on the loops.
  9. Be sure to use bolt (Loop Location) with the presence of a secret head. Otherwise, the floor will not get folded.
  10. Part of the bolts, which looks out of the reverse side gently cuts off with the help of a grinder. Drain nuts. To ensure maximum rigidity level, you should place 3-4 loops per connection.
  11. The resulting construction from above is covered with a piece of linoleum And it will be burned with felt-tip pen.
  12. Cut off the extra pieces using a jigsaw.
  13. We curl the edge over the entire contour, applying a file.
  14. Taking sandpaper, pollut the entire surface , cover it 3-4 layers of varnish (yacht form).

Anchor for boat

There are a large number of models of anchors for swimming agents. Most fishermen as an anchor often use any iron device suitable by weight. Some fishermen prefer to buy collapsible models.

Selecting anchor should consider certain requirements:

  • Mass should be at least 5-6 kg (depending on the strength of the streams of wind and the flow rate, the ship's sailboat is also of great influence);
  • The ability to raise and descend from the place of product management of the swimming agent. Boats, the length of which reaches 4 meters, is subject to equipment anchor ryom and a roller (optional). This will ensure the safety of the cord in the friction areas about the metal.

Spinning holders

Holders for spinning are more expedient to produce on the basis of plastic tubes. Each of the side is desirable to have 2 holder.

Holders for Spinning

Sensor Echohoto

The sensor of the echo sounder can be fixed with the suction cup, but in most cases on PVC boats, it is poorly held. As a solution of the problem, you can purchase an aluminum tube with the presence of a square section. We drill holes in the tube (cross-cutting), intended for the pintage.

We make a rhy-egg and fix with glue in the side upper area of ​​the cylinder. Adjust the immersion depth of the sensor can be easily moving pin. The bottom of the tube is equipped with a bracket for the sensor. Rotating it vertically, you can achieve the required level of inclination. Horizontal rotation is impossible due to the profile pipe.

Echo sounder on the boat

Transit wheels

Variants of creating transit wheels a huge set. The main purpose of the wheels is the transportation of a variable swimming agent from the trailer to the aquatic environment.

Step-by-step process of manufacture of wheels:

  1. We prepare inflatable wheels with a diameter of 300-400 mm and width of more than 100 mm. It is very important to select the largest diameters as much as possible, which will prevent from the fruit of the ground.
  2. Wheel sleeve connects to it as sealed as possible.
  3. The chassis can be made on the basis of chambers or pipes. The most simple fastening of the transaction to the chassis will become a metal plate, welded to the cutting of the pipe, in which the top area of ​​the chassis will be placed without the backup.
  4. All chassis mounts must have at least 3-4 points and plates (clamping type) located on the inside of the transom. It is they who will provide the maximum strength of fixtures.
  5. The chassis is fixed on the fastener with bolts. Optionally, the raising of the wheels can be provided along the cylinders.

Inflatable keel

Not every PVC boat is equipped with a keel. It is especially important its presence in swimming agents with the presence of a motor. Kiel has the following functions:

  • can ensure the deduction of the vessel in the course;
  • Prevents the ripping area of ​​the boat from the surface of the water stroit at the moments of movement with the motor turned on.

You can also make a keel!

  1. From waterproof materials, a tube grinds having a diameter of 100 mm with the presence of a valve.
  2. The required length tube is usually calculated By measuring the distance from the stern side to nasal.
  3. We glue the tube to the bottom of the bottom in the inside of the vessel in the place of keel Using the transverse stripes from PVC.
  4. It is advisable to pre-pour mustard mortar into the pipe which will ensure the level of tightness.
  5. Reaching shallow water from keel Be sure to go down the air.
Two boats PVC on the shore

Kiel prevents the head of the nose area of ​​the boat from the surface of the water stroit at the moments of movement with the motor turned on

Seat

The main part of the PVC boat store models is equipped with hard seats that deprive the fisherman comfort and do not allow for a long time with convenience. To ensure your own comfort of stay on the vessel, you can install soft seats on board, after having turned them with dermatin.

Alternatively, you can purchase inflatable chairs. If desired, the soft seat is complemented by a bag located under it and performing the storage feature of small parts. The sizes of the bag must be proportional to the size of the chair.

Engine insurance

Unfortunately, it is impossible to predict that it can happen to a boat after going into an open reservoir. Pretty frequent troubles in fishermen are unexpected collisions with obstacles. In this case, the poor cutting of the clamps can provoke a disruption of a boat engine from the location. Very often he simply goes to the bottom of the reservoir.

To eliminate this kind of misunderstandings, the engine strengthened. For this, the cable (synthetics or steel) is stretched (synthetics or steel) on the trans. bypassing ry-rings, which are placed on the trans. Speaking by a simple yazik, the motor is reliably asleep and it becomes impossible to lose it.

Awning

Tuning the tuning of the boat, fishermen are often equipped with a tent. The awnings are available on sale a variety of varieties and can be designed for certain models of ship. For small boats, the awning umbrellas are used, which are covered by a person from the rain and the sun.

Boats equipped with a motor often completed:

  • A nasal fairing - based on PVC material. Some models are complemented by an overview window. The awnings with ease are pounced on a special arc, replete people from splashes and not giving high waves to fall inside the boat. When the glyceing is performed, the nasal fairing performs the function of the anti-cycle, which prevents the swimming remedy in the air during the strong gusts of the oncoming wind. The presence of a small pocket allows you to store a copy of the side of the side.
  • Tent-transformer is attached to the aluminum arcs. The design is capable of covering people from rain drops and wind gusts. The windows located on the awning product make it possible to move under the engine (with a slight wind). The lateral parts of PVC matter are movable and can fasten with lightning, climb when fixing with pins. By changing the position of the lateral parts of the awning, you can comfortably spend the night on the water, to carry out fishing in rainy weather or getting into the land. Most models are equipped with ventilation devices.

Boat with seat

Table and hiking bags

For storage of useful trifles that can be useful on fishing, bags are actively used. They can be placed in the nose of the vessel or under the seat. To secure the bag, you should use the basic boat fasteners. You can build a small comfortable table on the vessel from a children's chairs for feeding (part of the plastic table).

Additional options

As an additional tuning, fishermen is carried out fastening the fastening of the gas tank and the equipment of the boat with an arc for spinning.

The fastening of the gas tank is a very important procedure that will not lose it with sharp turns or a strong course. A common tank is taped using a solid rope passed through a semiring.

Fix half rings in the following ways:

  • By gluing to the bottom (in cases where the floor inflatable);
  • If the floor is more expedient to fasten the semir rings to Paioline.

The arc for spinning fishermen is called bar. As a rule, it is performed on the basis of the pipe, attaching a rigging glass to install the tackle. Tarka is installed in the trove of the vessel or in the middle.

Blitz advice

  • By gluing accessories for an inflatable boat, you must use the adhesive basis of high quality (specialized).
  • Before you start gluing, both surfaces should be deguted.
  • Each of the glue layers are applied after 15-20 minutes, which is necessary for the polymerization of glue.

Fishing from the boat has many advantages and makes it possible to swim in the most inaccessible places of the reservoir. Allows the accurate cast and feeding. For spinningists, the entire horizon is open and you can try to try to catch a walk on the track or trick in your pleasure.

Unreal Primanka

Many fishermen spend in a boat for many hours, which brings some inconvenience. The rigid seat does not allow the muscles to relax, the motor control distracts from his beloved hobby, the fishing rod slides on the side. Variations set. All this can be avoided and making Tunning PVC boats for comfortable fishing with your own hands.

How can I spend tuning boats PVC

Taskuning task

Package set does not always meet personal needs, but it is always possible to upgrade it. Create comfort and comfort, improve buoyancy and wear resistance - the main tasks of tuning. Many details and items that will be needed for tuning boats PVC do it yourself, you can buy or find in our own garage and shed.

Raise wear resistance

During operation, the boat is subjected to different impacts. It is impossible to foresee all the features and no one is insured against unexpected damages.

Bottom

Perhaps most often suffers the bottom. It can be strengthened as follows:

  1. Inflate and turn the boat to the bottom up.
  2. Attach the material and make a pattern. You can strengthen the entire surface or individual sections. To do this, use PVC profile or other waterproof materials.
  3. Clean the bottom, wash and wipe dry.
  4. Switch the air.
  5. Run the surface on which you will work. Declaring with gasoline or White spirit.
  6. Apply glue and impose a latch. Show attention, you must remove all air bubbles. Surface fit should be durable. You can use the roller and during rolling you need to press the gluing location.
  7. It may take additional heating with a construction dryer, but it depends on the materials used.

After such a procedure, the wear resistance of the bottom increases significantly. But experienced fishermen warn that if you strengthen all the bottom boat with a kilogram on 8, so they are advised to impose marks only in particularly dangerous places for rupture. To enhance the flooded, you can buy a private bar or profile. They are of different thicknesses, sold in specialized stores, you can pick up a certain model, which makes it easier to choose.

Tuned boat

Cylinders

Strengthening cylinders also, like the bottom. The only difference is that when sticking a private brusade, the boat does not need to be blown away.

Sealing seams

Dear brand boat models during proper care do not need such action. And the plasticity simply does not prevent additional sizing compounds, especially if the boat with a motor. You can make a specific upgrade and use decorative stripes during sealing, which give the boat individuality and uniqueness.

Increase speed

Easy the management of the mournfulness under the motor will help the established keel. Make such a tuning boat PVC fishing with their own hands, will help the PVC profile glued to the bottom. With him, you will not be bored with the course and speed will increase, as resistance will be less. Such a keel lifts the nose and is not particularly highlighted on the stern.

Step-by-step instruction:

  1. Measure the length of the bottom and add 10 cm on the seams.
  2. On paper, draw a detail that narrows to the end.
  3. We try out the pattern to the inflated boat, if necessary, be customized.
  4. We apply the workpiece to the tissue and cut out, immediately need to schedule the location of the valve.
  5. Install the valve into the workpiece.
  6. We sample, tightly connecting items.
  7. Take the bandage regulator, fold it into two layers and place it in the deceased workpiece, glue.
  8. Generate and ride the ends of the keel.
  9. When the part of the cavity is dried, download and check with water.
  10. Mix the PVC strips with glue and get your keel to the bottom.

Hint! There are many ready-made drawings on the Internet that can be simply adjusted for example, do not forget to add 4 cm on the bending.

Boat after tuning on water

Hard floor

Boats are sold in completely different equipment and if the floor does not meet your requirements, it is easy to fix it. This will require:

  • plywood 10 mm thickness;
  • a piece of linoleum;
  • loops - 15 pcs;
  • bolts, washers and nuts;
  • Impregnation for plywood and yacht varnish.

Take the linoleum and make a pattern, for this attach it to the bottom with a minus cylinders. Then fold the resulting form in half and give symmetry. Then, on this size, cut 6 paisols. Collect the harmonica of them and connect the hinges.

Use the bolts with a secret head, especially from the loop side, otherwise the floor will not work out. Excess parts need to cut with a grinder and sharpen nuts. For each connection, put a minimum of three loops.

Then attach the Phaneur to the pattern, circle a pencil, then fir the jigsaw round and round down the lobsik. Treat the edges with a file and sandpaper, cover the impregnation and apply varnish 2 times.

Hint! Linoleum does not throw away, use it as a gasket between the bottom and the resulting floor.

Tuning hard floor

To protect PVC from abrasion when using hard floor, you can install stringers. For this use duraluminum profiles and corners. Stringors put on direct sites.

Holders for rod

For fishing from the boat, this very useful element can be purchased in the store or make a suitable diameter from PVC pipes. Holders extremely facilitate fishing and can be applied for both spinning and feeders.

Other options Tuning

Ideas for improving and upgrading boats is very much, especially if you see a photo on the Internet. Briefly about some:

  • Installing the console for remote control, which allows you to lead the boat from a convenient place for yourself.
  • Installing soft seats.
  • Equipment with transit wheels.
  • Production and installation of collapsible anchors.
  • Awnings, tents.
  • Additional insurance for the engine.
  • Installation of table and trolling crossbar.
  • Additional fasteners for transported things.

"There is no limit to excellence" - this statement directly can relate to tuning boats. Security and convenience in your hands. Change and improve your living conditions, and this video can be your assistant.

Share links:

Unreal Primanka

Tuning boats do it yourself - options for modifications, tuning directions and improvement of serial PVC boats (130 photos and video)

In specialized boats stores, mostly sell without all sorts of missions, so for convenience, each fisherman equips her at will. And this applies not only to PVC boats, although they are mainly subject to refinement.

Today we will look at the possible options for tuning boats for fishing with your own hands and tell me how to make some of them.

Tuning boats from PVC

This water vehicle is the most sold and convenient to use. This can be determined by the fact that:

  • the boat is easy to transport, do not buy any trailers;
  • It is easy to repaired;
  • For her there are many lotions.

But even considering all these positive moments, it is quite practical in the "cheese". The functionality of such a means is very small, which means that it is necessary to refine.

There are services where you can exercise your venture, but it costs quite expensive. Make tuning PVC boats will be cheaper and more correct.

Of course, this does not mean that all the details need to be mastered personally, some of them can be purchased in the store.

So let's look out that you can finish:

Strengthening the bottoms and cylinders. Such tuning experienced fishermen is always carried out, regardless of the conditions of the fishermen. It is proposed for the bottom and on the sides of the cylinders to glue an additional layer of rubberized fabric or membrane.

">

Initially, at an inflated boat, measurements are made and places are noted where the marks will be glued. After this, the boat is blown away, the places of gluing are degreased, and the selected material is glued on top.

If necessary, at the end, they still warm the hairdryer (construction). With such tuning it is worth considering that the weight of the boat will increase by an average of 5 kg.

Anchor. Very comfortable thing when fishing in one place. The stores sell a special anchor ryy, it is installed on the stern.

Sealing seams. When buying a cheap boat, you do not have to hope for quality. Therefore, many owners additionally seal seams.

You can also decorate the boat around the perimeter by various stickers, etc. To be able to inspire, you can see the photo of such tuning on the boat with your own hands.

Holder of rod. Also an indispensable thing, if fishing occurs at once a few spinning.

A list of things that can be supplemented with a swimming agent can continue infinitely. For example, you can install, seats, a table, steering wheel, to build wheels and a lot, a lot of other.

To get acquainted in more detail, we offer to watch the video tuning boats with your own hands.

Tuning fiberglass boats

In the case of such an aggregate, the variations of tuning are almost similar to the past. The main thing is to initially think about what you need for what purposes a boat will be used.

If for fishing, you immediately need to install spinning holders, anchor ryy and so on. When the tool is used as a family pastime (just swim), you can install seats such as rear and front.

You can even build a kind of boat, create a scheme, from the OSB panels to cut all the details and install directly on the boat housing. Then paint, open lacquer and dissect by waves.

The tuning of the fiberglass boat is not difficult to make, the main thing is to have a desire.

Aluminum boat tuning

These boats, like PVC, use the people in great demand, and causes this the strength of the hull, now no snag will be able to interrupt all fishing.

You can add such a tool:

  • Seats (if there is already there, then drag);
  • Windshields;
  • Additional covering of the housing in the form of chromium;
  • TEN (SPA);
  • Remote control, etc.

In addition, you can make a painting of the vessel. In general, make a mini yacht, in which it will not only be pleasantly riding, but also to swim for a kilometer from the shore and enjoy the open sea, drinking cocktails.

The tuning of the aluminum boat is very similar to the previous one.

Conclusion

As you could already guess, it all depends on your imagination and desire. After all, this is the fundamental success.

The main thing is not to be afraid of difficulties. Boats are a very good vehicle and attaching their hand to modernize them, you can recreate something unusual.

Photo tuning boats do it yourself

PVC boats are very valued by fishermen and they are considered to be one of the most convenient means of movement in water. Solid advantages that manifest themselves during operation are simply lost due to low functionality and minimal convenience. The boat purchased in the store requires improvements. The quality of materials involved in production is at a high level, which you will not say about the comfort for the fisherman.

Unreal Primanka

But, fishermen will not be easier to endure inconvenience during fishing, which very often turn it into torment. They have long come up with how to make a boat more convenient, practical and comfortable. This is the main purpose for which the Tuning of the PVC boat is done with their own hands.

Tuning boats PVC do it yourself

How to strengthen the bottom of an inflatable boat

How to strengthen the bottom of an inflatable boat

Manufacturers often make the bottom of the boat from PVC fabric, which is very inconvenient to walk. Without hard bottom provides a fisherman a number of inconvenience during a boat movement. Therefore, producing PVC boat tuning with your own hands, reinforce the bottom it is necessary first. Yes, and repair, if damaged, the strengthening will have, and not the bottom itself, which is significantly cheaper and easier. The bottom of the boat can be strengthened in whole or in part.

A special tape from PVC is perfectly coping with the task. Such a tape is also called the private bar and it is covered with the bottom of the boat completely or partially. Usually, the thickness of such a tape is from 1 to 3 millimeters, and the width of 60 to 230 mm. You can glue a private bar using two component glue. Such an easy operation gives stiffness to the bottom, and also provides additional protection against underwater obstacles.

How to strengthen keel

How to strengthen keel

The keel is enhanced as well as the bottom itself - over the ribbon, which is often equipped with a plant from the plant, glue an additional layer of a private bar. There are no subtleties and secrets here. We take two component glue and look at them the maximum keel area.

How to strengthen the cylinders

How to strengthen the cylinders

Cylinders are not reinforced for comfort, but from necessity. Most often, Tuning PVC boats with their own hands includes pasting a private bar across the entire area of ​​the bottom. Strengthening cylinders provides additional protection and prevents them with wear during operation.

How to strengthen trackers

How to strengthen trackers

Usually, when buying a boat in a standard configuration, you can see that the trauma protects only a small layer of PVC fabric. This is not very reliable protection. Therefore, it should be paid to the enhancement of the transaction at no less attention than for other elements.

Many fishermen prefer to fully stick the bottom of the boat by a private timber. So more reliably and machinations with individual elements. It will be the most correct solution, only you need to be extremely neat and select glue and a private bar. Such an approach to tuning will be able to solve a whole bunch of problems and relieve your boat from wear during long-term operation.

Installing Stringers

Installing Stringers

Duraluminum profile is a mandatory element for a rigid boat. The process of friction of tough Paiol about PVC material during the movement on the water simply can not be avoided. This friction is caused subsequently the deformation of the tissue during contact with water.

The consequences of such a process may occur quite a lot, ranging from partial damage to PVC tissue and ending with the deformation of the boat itself. Stringors do not need to be installed in the nasal part of the boat, and waters in places where the bottom will not interfere with the bottom.

Before mounting the profile, it is necessary to carefully place the boat and its bottom. Marking and installation is carried out according to the following algorithm:

  1. First, it is necessary to decompose Pioles on the floor in the same way with the compliance of the sequence and gaps as they are located in the boat.
  2. Stringer must be applied to one side of Pioles in such a way that it overlap the three neighboring Piols.
  3. As mentioned above, in the nose part of the boat, the stringers are not installed. Usually, during the movement of the main load, the rear of the boat is given. Therefore, the installation of stringers in the rear of the boat is mandatory.
  4. Pay attention to that during installation, no parts of the hard bottom are sticking to the side or drank off the edges. Therefore, it is better to place it in advance, so that the Stringer to Piol is painlessly handless.
  5. For the product of the drawing, it is necessary to apply Stringer to the extreme part of Piol and draw a flat line.
  6. Do not forget about the premium on each side on the length of the Stringer, it is about 4 cm. If you leave such a dummy, then you can easily shoot and wear stringers even directly on the reservoir.
  7. After the markup is completed, it is necessary to take the jigsaw and start making feeds on each side, according to the drawing. It is very important to use a special tree file for such purposes, otherwise you can ruin Pioli. Attentiveness and lack of hurry are very important in this process.
  8. After you have completed the propyl, you need to thoroughly treat it with a means to repulsion moisture. It can be any means that includes the maximum amount of wax, as an option, you can use Pinotex Focus. Olife or yacht varnish are usually applied fishermen to treat extreme sections.

How to fix a private bar

How to fix a private bar

The private bar is one of the main materials that provides the rigidity of the bottom of the boat and additional protection for the bottom, cylinders and a transom. Bloom this material is not difficult if you follow some simple recommendations:

  1. It is necessary to thoroughly wash the boat and remove all the dirt from it. After removing pollution, you need to dry the boat well. Even a small drop of water can significantly worsen the quality of the gluing elements.
  2. The connection site must be deguted. It is done very carefully not to disturb PVC fabric. It is possible to degrease the surface with acetone or gasoline.
  3. On both surfaces it is necessary to apply glue. This is done using the usual painting brush. The second layer of glue must be applied in 10-15 minutes. The second layer should be given to dry until the glue stops sticking to the hands.
  4. Now it is necessary to attach a private timber to the boat and carefully press your hands.
  5. To ensure greater reliability, the connection is carefully warmed with a hairdryer. It is necessary to warm in reasonable limits so as not to bring plastic to melting.
  6. After the warm up, it is necessary to squeeze the connected surfaces very much.

Installation of the Red

Installation of the Red

Redan is a special profile that is equipped with guides and in its design is somewhat similar to a triangle. The main task is to increase the stability of the boat while driving through the water. Often, the Tuning of the PVC boat does not do without installing this accessory.

Typically, the installation of the reinforcement is combined with additional control of the keel and boat cylinders, which is very convenient and practical. Small lengths are placed in the nose part of the boat, as it is there most often a lot of splashes are formed and it strongly affects stability.

True, these elements can be not only triangular, they have a different form, but the same purpose is to increase the stability of the boat during the gliding on the water. A very convenient and useful accessory that can be easily installed independently. They are also called coursework stabilizers.

Fastening anchor

Fastening anchor

Without anchor, you can hardly be at the desired point of the reservoir for a long time. To the tuning element, the anchor installation refers not much, rather is one of the mandatory elements for a swimming agent. When fishing, at all, it is difficult to delay the boat at one point of the reservoir, even a short period of time.

Anchor for PVC boat can be of different designs. Any type of iron that is suitable by weight can act as an anchor (I use the dumbbell weighing 6 kilograms). In stores you can find different models, including collapsible.

There are certain requirements that should be guided during an anchor selection in order not to encounter unpleasant fishing surprises:

  1. Depending on the sailboat boat, the flow rate, as well as wind power, you need to choose anchor with a mass of 5 to 7 kilograms;
  2. It is necessary to choose an anchor of such a mass and design so that it can be easily raised and pull into the water during fishing. Anchoring rhyh, preventing friction rope about the boat is installed on the vessel, more than 4 meters long.

Installing spinning holders

Installing spinning holders

Spinning holders are a very useful accessory. This is primarily convenient and practical, because if you gathered to catch fish by trolling, then hold in your hands more than one spinning alone will be a rather complicated occupation.

Usually, fishermen prefer to buy such holders in the store. If you plan to fish alone, then the PVC boat tuning provides for the installation of two mounts, for a pair of fishermen it is better to install three. Setting a larger number of holders can cause a number of inconveniences for fishermen. Yes, and fishing at the same time for a large number of spinning is not a rational and impractical solution.

Some fishermen do not buy holders, but make them themselves. Alternatively, you can simply cut a piece of PVC pipes of the necessary diameter and consolidate it on the boat. It is not very beautiful, but quite comfortable.

Installation of transcent

Installation of transcent

A trauma is a mandatory attribute of any boat that provides for the installation and use of the motor. But, despite the obligation, the traum may not be included in the package of the boat. The trauma is also the main element of the fastening of the echo sounder.

Usually, the hanging trauma is attached on the bracket. The bracket is attached to special attachments that are installed on the bottom and at the top of the boat cylinder. Some boats can be equipped with a certain tubular frame for installing the trans.

Ry for anchor

Ry for anchor

Ry shall establish on the feed of the boat and its main purpose is to simplify the process of lifting and lowering the anchor. This is a very convenient accessory that saves strength and fishing time. An important point is the placement of the video. To prevent abrasion of a private bar, it must be placed slightly lower.

Installing transit wheel

Installing transit wheel

The need for transit wheels is determined by the conditions of fishing, namely the characteristics of the reservoir. If you plan to fish in wild water bodies, then it will be enough to pull the boat normally in such conditions. Most often, fishermen descend the boat on their hands, so there is no need for transom wheels at all.

If fishing will still occur in conditions where you can pull the boat, then the transit wheels will never be superfluous. The main task of such wheels is a simple delivery of a loaded boat from the trailer to the shore of the reservoir and the subsequent descent on the water.

Let's consider in more detail The process of installing the wheels :

  1. First you need to get a pair of wheels with a diameter of about 40 centimeters and about 10 cm wide. The larger the diameter of the wheels, the better. Big wheels are smoking less in a loose ground.
  2. Now it is necessary to very tightly combine the sleeve with wheels.
  3. The chassis of fishermen is made of pipes or chambers. The easiest embodiment is a metal plate, which is welded to the pipe. The pipe should be of such a diameter so that it is possible to place the top area of ​​the chassis very tight.
  4. For the chassis to keep them as tightly tightly, they need to be fixed in 4-5 metal plates.
  5. Fasten the chassis is necessary for conventional bolts.

Installation of inflatable keel

Installation of inflatable keel

Cheap boats, often not equipped with a keel. The absence of keel sharply reduces the boat handling and adhere to the course becomes quite difficult. The problem of stability and simplification of management is solved quite simply - installation of inflatable keel.

The size of the keel is directly dependent on the size of the vessel. When installing an inflatable keel on a small boat (less than 3 meters long), you simply take her nose very high and do not receive a proper effect. Consign the keel is very simple, it is made by special ribbons that are included in the accessory package.

Seat installation

Seat installation

Almost all boats are equipped with harsh seats, on which it is very uncomfortable to sit throughout a large segment of time. Therefore, Tuning PVC boats usually provides for the installation of more convenient seats. Some fishermen modify factory seats, and some set new ones. Very convenient to place the boxes for a variety of fishing accessories under the seats of the boat.

A convenient solution is to install a moving seat that can be fixed at any point of the swimming agent.

You can buy an inflatable seat in the store, but it is not quite practical, so you have to make it yourself. You will need to get two boards from the pine, the length of which will depend on the distance between the boat cylinders, and the width of your weight, also need to take care of the possibility of folding the seats, for this you will need former fittings, as well as seat belts.

  • It is necessary to combine the boards by means of fitting fittings.
  • It is necessary to fix seat belts on both sides of the seating with screws.
  • Belts should pass through the bottom, and the adjustment of the seats is carried out already on the boat itself.
  • On the boards you need to impose a thick foam and close it with a cover that can be sewed from tarpaulin or cloaks.
  • Velcro or zipper can be used as a tarpaulin fastener.

The possibility of free displacement of such a boat seating and its budget is made by this version of tuning one of the best. In the store you can find the seats are more practical, but their price will be much higher, and the described option will cost you in a penny.

A bag

A bag

Most often, the bag for accessories and various fishing facilities is installed in the nose part of the boat or hide under the seats. This is a very convenient thing in which you can put various useful little things.

Basic boat fasteners perfectly copes with the functions of the retainer for the bag. You can also do a small table. For this purpose, a children's chair for feeding is perfect. This is a convenient equipment that will greatly simplify the fishing process.

Insurance for motor

Insurance for motor

Often, unpredictable things are happening on fishing, which makes it a very dangerous, but also an interesting occupation. One of the common abnormal situations is a motor break. Exodus in such a situation one - the departure of the engine under water. You can prevent the broken by the insurance, which is carried out using a cable. Motor should simply bind through 2-4 rhy rings to the transnt.

It is used as an ordinary, metal cable and artificial. It all depends on the weight of your motor, as well as on financial opportunities. In any case, metal insurance will provide the maximum effect.

Installation of fastening for gas tank

Installation of fastening for gas tank

When the PVC boat tuning is made with their own hands, the gas tank is made at the bottom of the boat, which is one of the main factors provided by security. The fastening of the gas tank must be in each boat, regardless of the type of bottom.

With a reliable fixation of the gas tank, you can safely move around the water, without thinking that your tank will fly into the other side of the boat or will fall out with her at all. Stoporks, screws and semirings are most often used for tank fixations.

You need to take a semir of stainless material and consolidate them on the bottom of the boat. If the bottom is inflatable - fastened with waterproof glue, and if the bottom is rigid, then you can fasten with their screws directly to Piolas. It remains only to tie a tank to half rings with a rope or cable.

In the same way, you can mount the drawers with accessories, as well as other little things and equipment.

Fasteners for mounted equipment

The remaining elements that are additional equipment can be fixed with two-component glue. True, universal fastening systems are also known among fishermen. There are quite a lot of them, but only two types received special distribution. Installing such systems allows you to mount any hinged equipment to the boat without much effort.

Fastening "Pile"

Fastening "Pile"

This is one of the most convenient and versatile fasteners, which allows you to adapt to the boat fastening for spinning, awning, table or steering wheel. This type of fastener is made of PVC fabric, which can be simply glued to the boat using two-component glue.

Fasten fasteners

Fasten fasteners

Fast and universal fastening system. The singular highlight of such a system is the possibility of transformation to any types of attachments. This mount is suitable for installing a echo sounder or navigator, belt or spinning holders and a lot of other. The design of the system allows you to quickly change one type of fastener to another.

PVC boat tuning opens a lot of opportunities to ensure comfort and amenities during fishing. True, the installation of all accessories significantly increases the weight of the swimming agent, so it is worth thinking hard to install this or that equipment.

Unreal Primanka

Good day!

I post the result of my work above the boat, maybe my experience who is useful is to be useful. I have been implemented as an idea being taken from different topics of the site.

The boat is used for fishing, underwater hunting, pokatushek.

Photo 1.

What is actually done (in order of priority):

1. Transtese wheels (self-made).

Photo 2.

2. From aluminum pipes D = 25mm, longitudinal rails are made to which the post of management, the seat was already fixed in the future. Everything is collected on standard joker tube system connectors. All mounted attached to pipes with plastic pipe clamps.

Photo 3.

3. Mounted doof.

Photo 4.

Photo 5.

Photo 6.

Photo 7.

4. The voltage regulator VRNL-1 is installed.

Photo 8.

5. Echo sounder is installed (the sensor is glued to the bottom of the silicone sealant). Deaths only according to the water temperature indications (2-3 degrees).

Photo 9.

6. The TINY-TUCH tachometer is installed and connected to the candle wires;

Photo 10.

7. Navigator is installed on the console. On the floor cut the floor coating on the rubber base. All rubbish, sand accumulates on it. This coating is fairly easy to wash Kershehher or simply shaking; 9. On the left board to the longitudinal line and the paddle is fixed a table with the help of plastic locks.

Photo 11.

Photo 12.

10. Motovilo, with the faer for anchor, is also fixed to the longitudinal rail with the help of plastic locks. At the flow, I do not fuck and do not fuck, so it is enough for me to be fixed, so as not to demolish the wind.

Photo 13.

Photo 14.

11. Anchor translate in a plastic tube for sewage (photo 4) .12. On the right between the wheel and the seat on the fixators are fixed by boxing for documents, keys, telephone, etc. Smart (photo 5) .13. When I go alone, the benzobak fasten with the screeds on the stern, there is Schmurdak. When with passengers, then gas tank back to the transnt, passengers on the nose (photo 3) 14. Under the seat, a container is conveniently located (plastic boxing on latches) with food.

Photo 15.

15. In order to in the heat, he did not bake his head headed the running awning.

Photo 16.

16. For lifting water into the boat after hunting from aluminum pipes and fasteners, Joker collected a ladder. Fucked by hooks to the rail on the left side (unfortunately there are no pictures).

Who is interested, ask questions.

Good luck to all!

Добавить комментарий